transient voltage suppressors smdj series speci?cations are subject to change without notice. please refer to http://www.ruilon.com for current information. electronic s circuit prote ct io n system
page:1 speci?cations are subject to change without notice. please refer to http://www.ruilon.com for current information. transient voltage suppressors - smdj series features mechanical characteristics rating symbol value units peak pulse power dissipation by 10x1000s test waveform (fig.1)(note 1) p ppm 3000 watts steady state power dissipation on ini? nite heat sink at tl=75c (fig. 5) p d 6.5 watts peak forward surge current, 8.3ms single half sine wave unidirectional only (note 2) i fsm 300 amps maximum instantaneous forward voltage at 25a for unidirectional only (note 3) v f 3.5 v operating junction and storage temperature range. t j , t stg -55c to 175c c typical thermal resistance junction to lead r ujl 15 c/w typical thermal resistance junction to ambient r uja 75 c/w notes: 1. non-repetitive current pulse , per fig. 3 and derated above ta = 25c per fig. 2. 2. mounted on copper pad area of 0.31x0.31 (8.0 x 8.0mm) to each terminal. 3. measured on 8.3ms single half sine wave or equivalent square wave for unidirectional device only, duty cycle=4 per minute maximum. 1. halogen-free 2. rohs compliant 3. typical maximum temperature coef ?cient 4. v br = 0.1% x v br @25c x t 5. glass passivated chip junction in do-214ab package 6. 3000w peak pulse capadility at 101000s waveform, repetition rate (duty cycles):0.01% 7. fast response time:typically less than 1.0ps from 0 volts to bv min 8. excellent clamping capability 9. low incremental surge resistance 10. typical ir less than 5a above 12v 11. high temperature soldering guaranteed: 260c/40 seconds / 0.375, 12. (9.5mm) lead length, 5lbs., (2.3kg) tension 13. plastic package has underwriters laboratory fammability classi?cation 94v-0 tvs devices are ideal for the protection of i/o interfaces,vcc bus and other vulnerable circuits used in telecom, computer , industrial and consumer electronic applications. uni bi uni bi anode cathode applications circuit prote ct io n system
transient voltage suppressors - smdj series page:2 speci?cations are subject to change without notice. please refer to http://www.ruilon.com for current information. electriacl characteristics type number device marking code reverse stand-off voltage breakdown voltage@i t test current maximum clamping voltage@i pp peak pulse current reverse leakage @v rwm (uni) (bi) uni bi v rwm (v) v br min. (v) v br max. (v) i t (ma) v c (v) i pp (a) i r (a) smdj5.0a smdj5.0ca hde ide 5.0 6.40 7.25 10 9.2 326.1 800 smdj6.0a smdj6.0ca hdg idg 6.0 6.67 7.67 10 10.3 291.3 800 smdj6.5a smdj6.5ca hdk idk 6.5 7.22 8.30 10 11.2 267.9 500 smdj7.0a smdj7.0ca hdm idm 7.0 7.78 8.95 10 12.0 250.0 200 smdj7.5a smdj7.5ca hdp idp 7.5 8.33 9.58 1 12.9 232.6 100 smdj8.0a smdj8.0ca hdr idr 8.0 8.89 10.23 1 13.6 220.6 50 smdj8.5a smdj8.5ca hdt idt 8.5 9.44 10.82 1 14.4 208.3 20 smdj9.0a smdj9.0ca hdv idv 9.0 10.00 11.50 1 15.4 194.8 10 smdj10a smdj10ca hdx idx 10.0 11.10 12.80 1 17.0 176.5 5.0 smdj11a smdj11ca hdz idz 11.0 12.20 14.00 1 18.2 164.8 5.0 smdj12a smdj12ca hee iee 12.0 13.30 15.30 1 19.9 150.8 5.0 smdj13a smdj13ca heg ieg 13.0 14.40 16.50 1 21.5 139.5 5.0 smdj14a smdj14ca hek iek 14.0 15.60 17.90 1 23.2 129.3 5.0 smdj15a smdj15ca hem iem 15.0 16.70 19.20 1 24.4 123.0 5.0 smdj16a smdj16ca hep iep 16.0 17.80 20.50 1 26.0 115.4 5.0 smdj17a smdj17ca her ier 17.0 18.90 21.70 1 27.6 108.7 5.0 smdj18a smdj18ca het iet 18.0 20.00 23.30 1 29.2 102.7 5.0 smdj20a smdj20ca hev iev 20.0 22.20 25.50 1 32.4 92.6 5.0 smdj22a smdj22ca hex iex 22.0 24.40 28.00 1 35.5 84.5 5.0 smdj24a smdj24ca hez iez 24.0 26.70 30.70 1 38.9 77.1 5.0 smdj26a smdj26ca hfe ife 26.0 28.90 33.20 1 42.1 71.3 5.0 smdj28a smdj28ca hfg ifg 28.0 31.10 35.80 1 45.4 66.1 5.0 smdj30a smdj30ca hfk ifk 30.0 33.30 38.30 1 48.4 62.0 5.0 smdj33a smdj33ca hfm ifm 33.0 36.70 42.20 1 53.3 56.3 5.0 smdj36a smdj36ca hfp ifp 36.0 40.00 46.00 1 58.1 51.6 5.0 smdj40a smdj40ca hfr ifr 40.0 44.40 51.10 1 64.5 46.5 5.0 smdj43a smdj43ca hft ift 43.0 47.80 54.90 1 69.4 43.2 5.0 smdj45a smdj45ca hfv ifv 45.0 50.00 57.50 1 72.7 41.3 5.0 smdj48a smdj48ca hfx ifx 48.0 53.30 61.30 1 77.4 38.8 5.0 smdj51a smdj51ca hfz ifz 51.0 56.70 65.20 1 82.4 36.4 5.0 smdj54a smdj54ca hge ige 54.0 60.00 69.00 1 87.1 34.4 5.0 smdj58a smdj58ca hgg igg 58.0 64.40 74.10 1 93.6 32.1 5.0 smdj60a smdj60ca hgk igk 60.0 66.70 76.70 1 96.8 31.0 5.0 smdj64a smdj64ca hgm igm 64.0 71.10 81.80 1 103.0 29.1 5.0 smdj70a smdj70ca hgp igp 70.0 77.80 89.50 1 113.0 26.5 5.0 smdj75a SMDJ75CA hgr igr 75.0 83.30 95.80 1 121.0 24.8 5.0 smdj78a smdj78ca hgt igt 78.0 86.70 99.70 1 126.0 23.8 5.0 smdj85a smdj85ca hgv igv 85.0 94.40 108.20 1 137.0 20.8 5.0 smdj90a smdj90ca hgx igx 90.0 100.00 115.50 1 146.0 20.6 5.0 smdj100a smdj100ca hgz igz 100.0 111.00 128.00 1 162.0 18.6 5.0 smdj110a smdj110ca hhe ihe 110.0 122.00 140.50 1 177.0 16.8 5.0 smdj120a smdj120ca hhg ihg 120.0 133.00 153.00 1 193.0 15.6 5.0 smdj130a smdj130ca hhk ihk 130.0 144.00 165.50 1 209.0 14.4 5.0 smdj150a smdj150ca hhm ihm 150.0 167.00 192.50 1 243.0 12.4 5.0 smdj160a smdj160ca hhp ihp 160.0 178.00 205.00 1 259.0 11.6 5.0 smdj170a smdj170ca hhr ihr 170.0 189.00 217.50 1 275.0 11.0 5.0 smdj180a smdj180ca hht iht 180.0 198.00 230.40 1 292.0 10.3 5.0 smdj190a smdj190ca hhv ihv 190.0 209.00 243.20 1 308.0 9.7 5.0 smdj200a smdj200ca hhx ihx 200.0 220.00 256.00 1 324.0 9.3 5.0 smdj210a smdj210ca hhz ihz 210.0 231.00 268.80 1 340.0 8.8 5.0 smdj220a smdj220ca hie iie 220.0 242.00 281.00 1 356.0 8.4 5.0 circuit prote ct io n system
page:3 speci?cations are subject to change without notice. please refer to http://www.ruilon.com for current information. transient voltage suppressors - smdj series ratings and characteristic curves figure 2 - pulse der ating cur ve figure 3 - pulse w av ef or m figure 4 - t ypical junction capacitanc e figure 5 - st eady stat e po we r der ating cur ve figure 6 - maximum non-repetiti ve p eak fo rw ar d surg e curr ent uni-dir ectional onl y figure 1 - p eak pulse p owe r rating cur ve a circuit prote ct io n system
transient voltage suppressors - smdj series page:4 speci?cations are subject to change without notice. please refer to http://www.ruilon.com for current information. soldering parameters fefow condition lead-free assembly pre heat - temperature min (t s(min) ) 150c - temperature max (t s(min) ) 200c - time (min to max) (t s ) 60-180 secs average ramp up rate (liquidus temp (t l ) to peak 3c/second max t s(max) to t l - ramp-up rate 3c/second max refow - temperature (t l ) (liquidus) 217c - time (min to max) (t s ) 60-150 seconds peak temperature (t p ) 260 +0/-5 c time within 5c of actual peak temperature (t p ) 20-40 seconds ramp-down rate 6c/second max time 25c to peak temperature (t p ) 8 minutes max. do not exceed 280c physical specifcations weight 0.007 ounce, 0.21 grams case jedec do214aa. molded plastic body over glass passivated junction polarity color band denotes cathode except bidirectional. termina matte tin-plated leads, solderable per jesd22-b102d environmental specifcations temperature cycle jesd22-a104 pressure cooker jesd 22-a102 high temp. storage jesd22-a103 htrb jesd22-a108 thermal shock jesd22-a106 circuit prote ct io n system
page:5 speci?cations are subject to change without notice. please refer to http://www.ruilon.com for current information. transient voltage suppressors - smdj series dimensions dim inches millimeters min max min max a 0.114 0.126 2.900 3.200 b 0.260 0.280 6.600 7.110 c 0.220 0.245 5.590 6.220 d 0.079 0.103 2.060 2.620 e 0.030 0.060 0.760 1.520 f - 0.008 - 0.203 g 0.305 0.320 7.750 8.130 h 0.006 0.012 0.152 0.305 i 0.129 - 3.300 - j 0.094 - 24.00 - k - 0.165 - 4.200 l 0.094 - 2.400 - unit:mm do-214ab (smd j-bend) part numbering system vo lt ag e bi-directional 5% v ol ta ge t olerance series xx xc a smdj packaging part number component package quantity packaging option packaging speci?cation smdjxxxxx do-214ab 3000 tape & reel-16mm/13''tape eia std rs-481 circuit prote ct io n system
page:6 speci?cations are subject to change without notice. please refer to http://www.ruilon.com for current information. ruilongyuan electronics co., ltd. reproducing and modifying information of the document is prohibited without permission from ruilongyuan international inc. ruilongyuan international inc. reserves the rights to make changes of the content herein the document anytime without noti?cation. please refer to our website for the latest document. ruilongyuan international inc. disclaims any and all liability arising out of the application or use of any product including damages incidentally and consequentially occurred. ruilongyuan international inc. does not assume any and all implied warranties, including warranties of ?tness for particular purpose, non-infringement and merchantability. applications shown on the herein document are examples of standard use and operation. customers are responsible in comprehending the suitable use in particular applications.ruilongyuan international inc. makes no representation or warranty that such applications will be suitable for the specifed use without further testing or modifcation. the products shown herein are not designed and authorized for equipments requiring high level of reliability or relating to human life and for any applications concerning life-saving or life-sustaining, such as medical instruments, transportation equipment,aerospace machinery et cetera. customers using or selling these products for use in such applications do so at their own risk and agree to fullyindemnify ruilongyuan international inc. for any damages resulting from such improper use or sale. tel: +86-755-8290 8296 fax: +86-755-8290 8002 e-mail: jack@ruilon.com circuit prote ct io n system
|
